Home > Amplifiers >

Manley Snapper Mono Block Amplifiers Used

Manley Snapper Mono Block Amplifiers Used


 
Alternative Views:


List Price: $8,399.00
Our Price: $4,000.00
Savings: $4,399.00


Product Code: USE9000117
Qty:

Description
 
Use pair of Manley Snapper Mono Block power amplifiers in very good condition. Actual pictures of the amps shown.

100 Watts at full power across the entire frequency band from a quartet of EL34’s in a fully differential circuit topology is only achievable with an impressive 19-layer output transformer designed and wound by us here at Manley Labs, of course. Very cleverly, the Snapper’s unique fully balanced topology can be driven via the XLR inputs or by the unbalanced RCA’s with no sonic penalty either way. Until you have experienced these beauties, you have no idea how great these Snappers sound. Strong and natural, like real music.

SPECIFICATIONS

Input Impedance RCA: 475 Kohm

Input Impedance XLR: 15 Kohm or 600 Ohm switchable

Input Sensitivity RCA: 750mV input = 110W output

Input Sensitivity XLR @ 15Kohms: 1.5 V input = 110W output

Input Sensitivity XLR @ 600 Ohms: 2.4 V input = 110W output (w/600 Ohm source)

Gain RCA: factory set for 31 dB; Range = 29.5 to 34.5dB

Gain XLR: factory set for 25 dB

Negative Feedback: factory set for 9dB of global NFB

Maximum Output Power into 5 Ohms: 110 Watts (1.5% THD @ 1kHz)

Maximum Output Power into 8 Ohms: 100 Watts (1.5% THD @ 1kHz)

Signal to Noise Ratio Ref. 1W: Typically 90 dB A-WGT 20-20K

Noise Floor: Typically 105μV = -77dBu A-WGT
Typically 388μV = -66dBu unweighted

Dynamic Range: 98dB

THD+noise @ 1W: less than 0.1%

Frequency Response at 110W full power: 15 Hz to 40 kHz FLAT

Frequency Response at 5W into 5 Ohms: 10 Hz to 65 kHz FLAT, -3dB @ 100KHz

Recommended Speaker Load: Optimized for 5 Ohms

Actual Output Impedance: 1.5 Ohms

Power Consumption (idle): 170 Watts (1.4A @120VAC)

Power Consumption (at Full Power 110W): 336 Watts (2.8A @120VAC)

Operating Mains Voltage: Factory set for 120V AC operation for original destination country's mains voltage.

Operating Mains Voltage: changeable with power transformer re-wiring and fuse value change.

Mains Voltage Frequency: 50~ 60Hz

Tube Complement (per pair of Snappers):

Input Vacuum Tube: 2 x Ruby 12AX7 (matched pair)

Driver Vacuum Tube: 2x 5687 or 7044 (equivalent) (matched pair)

Output Vacuum Tubes: 8 x Tungsol EL34B (matched)

B+ Voltage: 570V DC

Output Tube Quiescent Standing Current: 30mA

Set Bias for: 300mVDC measured across 10 Ohm cathode resistor

Lamp type: "FuseLamp" size 1/4" X 1 1/4", 12 volt, 0.15 amp; Units built after 5/2003 use white LEDs

Fuse values & types for:

120VAC operation: MDL or MDA 4 AMP / 250 Volt SLO-BLO size 1/4" X 1 1/4"
B+ FUSE: MDA 1/2A Ceramic SLO-BLO size 1/4" x 1 1/4"

Dimensions: 15" deep x 13" wide x 8.75" tall

Shipping weight each: 45 pounds




Share your knowledge of this product. Be the first to write a review »