Clean, Stable AC Power for Your Components
The PS-1250 Clean Power Supply is an AC power regenerator with waveform shaping that rebuilds the power your components run on. Rather than only filtering the wall supply, it generates a precise reference sine wave, compares the incoming supply with it, adds what is missing and removes what is excess, then delivers the corrected waveform through its waveform correction amplifier. The result is an output with 0.08% or less distortion, rated at 900 VA continuous, from household mains that are typically distorted.
It is the sixth generation of the series Accuphase began with the PS-1200 in 1997, and the larger of its two current models. A color display shows the wall supply and output waveforms, along with output power, input and output voltage, and input and output distortion, so you can see what it is doing and how much of its capacity your system uses. Eight AC outlets serve sources, preamplifiers and amplifiers within its 900 VA rating.
TTVJ is an authorized Accuphase dealer. You're buying through the brand's own dealer network, with advice from someone who has set up these components in real listening rooms.
How It Cleans Your Power
Three Stages of Noise Removal
- Line filter: removes noise from digital and similar equipment on the line.
- Shielded toroidal transformer: removes common-mode noise.
- Waveform correction amplifier: shapes the waveform into a clean output.
Waveform Shaping
The PS-1250 detects the zero-cross point of the mains and creates a square wave, then passes it through band-pass and band-elimination filters to form a harmonic-free reference sine wave. The incoming supply is compared with that reference: missing portions are supplemented and excess distortion removed. Because the output is shaped as pure AC, with no conversion to DC, efficiency is improved, and because no oscillator is used, the risk of generating high-frequency noise is eliminated.
Sizing It for Your System
Watts, VA and the 900 VA Limit
Components are rated in watts, but the PS-1250's capacity is measured in VA. A component's VA is generally 1.2 to 1.8 times its wattage rating, depending on the component. Keep the total connected load under 900 VA. Integrated and power amplifiers draw more as the volume goes up, so their load should stay below 900 VA at maximum volume.
The output power meter shows the load from 0 to 1,200 VA. If it exceeds 1,200 VA, the display selector LED blinks; disconnect equipment until it stays steady.
Where It Can Be Used
- On a regular household circuit of the voltage marked next to the rear AC connector (120 V in the US).
- Not on portable, aircraft or ship generators, or other non-mains sources.
- For audio and video components, not for household appliances, industrial equipment, or medical and other safety-critical equipment.
What the Display Shows
Display Modes
| Input/output waveform | The wall supply and the PS-1250's output, so you can see the effect of waveform shaping |
|---|---|
| Output power | Total load, 0 to 1,200 VA |
| Input/output voltage | With a green zone of ±10% of nominal |
| Input/output distortion | 0 to 6% |
| Display off | A switch turns the display off while you listen |
Is the PS-1250 Right for You?
A Great Fit If You Want
- To clean up distorted mains: a regenerated sine wave with 0.08% or less distortion.
- A stable voltage: rated output 120 V ±1.5 V, with output voltage correction.
- Capacity for amplifiers: 900 VA continuous across eight outlets, as long as the total stays under 900 VA at maximum volume.
- To see the result: input and output waveforms, load, voltage and distortion on the display.
Consider Something Else If You Need
- More than 900 VA: large power amplifiers at full volume can exceed it; ask Todd before connecting them.
- A smaller, lighter unit for a lower load: the PS-550, at 400 VA and 24.4 kg.
- A shallow shelf: the PS-1250 is 499 mm (19.6 in) deep and weighs 42.1 kg (92.8 lb).
PS-1250 vs. PS-550
Accuphase's Two Clean Power Supplies
| PS-1250 | PS-550 | |
|---|---|---|
| Rated output capacity | 900 VA continuous | 400 VA continuous |
| Rated output current (120 V) | 7.5 A | 3.4 A |
| Output power meter | 0–1,200 VA | 0–510 VA |
| Output stage | 20-parallel push-pull | 10-parallel push-pull |
| Filtering capacitors | 2 × 48,000 µF/100 V | 2 × 22,000 µF/90 V |
| AC outlets | 8 | 6 |
| Output THD | 0.08% or less | 0.08% or less |
| No-load consumption (120 V) | 37 W | 27 W |
| Height × depth (120 V) | 243 × 499 mm | 181 × 385 mm |
| Weight (120 V) | 42.1 kg | 24.4 kg |
Choose the PS-1250 If You
- Need more than 400 VA: 900 VA continuous, for systems that draw more.
- Have more than six components: eight outlets.
Choose the PS-550 If You
- Want lower idle consumption: 27 W at no load, against 37 W, for a system that stays within 400 VA.
- Need a smaller unit: 181 mm high and 385 mm deep, at 24.4 kg.
Not Sure Which to Choose?
Deciding between the PS-1250 and the PS-550, or whether your amplifier fits within either one? Todd can talk it through with you.
Design
Built Like a Stereo Power Amplifier
The layout is symmetrical, like an Accuphase stereo power amplifier: a large power supply in the center, with a large, high-efficiency shielded toroidal transformer and two 48,000 µF filtering capacitors, and a power amplifier block on each side. Each block has two circuits of 10 parallel bipolar transistors, forming Accuphase's 20-parallel push-pull output stage, driven fully in parallel for high peak current and low output impedance. The blocks take balanced inputs and are connected in balanced form.
Outlets, Protection and Finish
Internal output wiring to the outlets is all the same length, to keep performance consistent from outlet to outlet. The PS-1250 has high-grade output voltage correction, an inrush prevention circuit, and high-sensitivity protection circuitry, including temperature sensing, that guards the unit and the connected equipment against abnormalities. Cooling is natural, by convection. The side panels are high-gloss aluminum, and the front panel is champagne colored.
What's New Over the PS-1230
- Color LCD: shows the input and output waveforms, alongside power, voltage and distortion.
- More precise reference signal generator for waveform shaping.
- Rated capacity: 900 VA continuous, against the PS-1230's 1,000 VA (120 V versions).
Specifications
Accuphase PS-1250 Specifications
| Type | AC power regenerator with waveform shaping |
|---|---|
| Rated output capacity | 900 VA, continuous |
| Rated output voltage | 120 V ±1.5 V (230 V version: 230 V ±3.0 V) |
| Rated output current | 7.5 A (230 V version: 3.9 A) |
| Output frequency | 50 or 60 Hz, same as input |
| Output waveform distortion | 0.08% or less |
| Rated input voltage | 120 V ±10% (230 V version: 230 V ±10%), 50/60 Hz |
| Output stage | 20-parallel push-pull, bipolar transistors |
| Power supply | Large shielded toroidal transformer; 2 × 48,000 µF/100 V filtering capacitors |
| AC outlets | 8 (outlet shape differs by version) |
| Display | Color LCD: input/output waveform, output power (0–1,200 VA), input/output voltage, input/output distortion (0–6%); display off switch |
| No-load power consumption | 37 W (230 V version: 55 W) |
| Cooling | Natural air cooling |
| Dimensions (W × H × D) | 465 × 243 × 499 mm (18.3 × 9.6 × 19.6 in) |
| Weight | 42.1 kg (92.8 lb) net (230 V version: 41.3 kg); 51 kg (113 lb) in carton |
| In the box | AC power cord |
Order Your Accuphase PS-1250
As an authorized Accuphase dealer, TTVJ handles your order personally, from confirming the configuration to delivery. Reach Todd by phone or message to:
- Confirm current pricing and availability
- Discuss a trade-in of your current power conditioner
- Ask about financing and shipping
