Skip to product information
1 of 6

ATC

ATC SCM300ASLT Active Tower Speakers

ATC SCM300ASLT Active Tower Speakers

Regular price $85,999.00 USD
Regular price $85,999.00 USD Sale price $85,999.00 USD
Sale Sold out
Item may qualify for free US Shipping.
View full details

ATC SCM300ASLT: Flagship Active Tower

The ATC SCM300ASLT is a three-way active floorstanding loudspeaker and the flagship of ATC's Tower series. Each speaker has twin 15-inch Super Linear bass drivers, ATC's 75 mm Super Dome midrange and a 25 mm soft-dome tweeter. Each speaker is driven by its own ATC P4: a rack-mount, four-channel Class AB amplifier with built-in active crossovers that sends 275 W to each bass driver, 200 W to the midrange and 100 W to the tweeter, 850 W per speaker.

You add a preamp or a source with a variable XLR output. There's no power amplifier or speaker crossover to buy: the two P4 amplifiers handle both. Prefer to use your own power amplifier? See the passive version, the ATC SCM300PSLT.

Design3-way active tower, twin 15" SL bass
AmplificationATC P4 per speaker, 850 W
Bass Extension25 Hz (−6 dB, free-standing)
Max. SPL121 dB continuous at 1 m
InputBalanced XLR, 2 V sensitivity
P4 Placement5U rack unit, 5 m cable (up to 20 m)

TTVJ is an authorized ATC dealer. Every unit we sell is brand new, and Todd's advice comes from setting up ATC loudspeakers in real listening rooms.

Is It Right for You?

A Great Fit If You Want

  • A complete active system for a large room: speakers, amplifiers and crossovers matched by ATC.
  • An active crossover that splits the signal before the amplifiers, so each of the four drivers per speaker has its own amplifier channel with no passive crossover in between.
  • Very high output: 121 dB continuous at 1 m.
  • Bass to 25 Hz from two 15-inch drivers per speaker.
  • Amplifiers that can sit in a rack or on shelving away from the speakers.

Consider Something Else If You Need

  • To use your own power amplifier: the passive SCM300PSLT (see the comparison below).
  • A narrower tower with the same P4 system: the SCM200ASLT (see the comparison below).
  • Amplifiers built into the speaker, with no rack or shelf space for two 5U amplifiers: the SCM150A Classic.

Design

Twin 15 in SL Bass

Two full-spec 375 mm bass drivers with ATC's Super Linear (SL) magnet technology, each on its own 275 W amplifier channel. Free-standing, the response reaches 25 Hz (−6 dB). The active filters include a +6 dB bass EQ at 40 Hz.

75 mm Super Dome Mid

ATC's soft-dome midrange covers 380 Hz to 3.5 kHz on its own 200 W channel, the range where voices sit.

25 mm Soft Dome HF

The soft-dome tweeter takes over above 3.5 kHz on a 100 W channel, with thermal protection.

One ATC P4 Amplifier Per Speaker

Each speaker comes with its own ATC P4, a four-way mono-block amplifier made only for ATC active systems. It holds the three-way active crossover (380 Hz and 3.5 kHz, 4th order with phase correction) and four Class AB amplifiers built on ATC's grounded-source design: 275 W for each bass driver, 200 W for the midrange and 100 W for the tweeter. The P4 is a 19-inch, 5U rack unit weighing 35.8 kg, and it connects to its speaker with one 8-way cable. Full P4 specifications are listed under Specifications.

SCM300ASLT vs SCM300PSLT

Active or Passive: The Differences

The SCM300ASLT and the passive SCM300PSLT share the same cabinet, drivers, finishes and warranty. They differ in how they are driven:

Difference SCM300ASLT SCM300PSLT
Amplification One ATC P4 per speaker, 850 W (included) Your own power amplifier
Crossover Active, inside the P4, 4th order Passive, inside the speaker, 2nd order
Connection Balanced XLR from a preamp, 2 V Tri-wire binding posts
Sensitivity / impedance n/a 93 dB/W/m, 8 Ω
Max. SPL (1 m) 121 dB 120 dB
Bass EQ +6 dB at 40 Hz in the active filters None
What you connect A preamp or source with a variable XLR output An integrated amplifier, or a preamp and power amplifier
Space and power Two 5U P4 amplifiers (included), each with its own mains connection Your amplifier (not included)

Choose the SCM300ASLT If You

  • Want a complete system without buying a power amplifier: ATC's P4 amplifiers and active crossovers are included.
  • Want each driver on its own amplifier channel, with no passive crossover between amplifier and driver.

Choose the SCM300PSLT If You

  • Already own, or want to choose, your own power amplifier.
  • Want to use an integrated amplifier, or prefer not to house two 5U rack amplifiers.

SCM300ASLT vs Other ATC Active Models

SCM300ASLT, SCM200ASLT and SCM150A Classic

Feature SCM300ASLT SCM200ASLT SCM150A Classic
Format Tower Tower Classic, on stand
Bass drivers 2 × 375 mm SL 2 × 314 mm SL 1 × 375 mm SL
Mid / HF 75 mm Super Dome / 25 mm 75 mm Super Dome / 25 mm 75 mm / 25 mm
Crossover points 380 Hz, 3.5 kHz 380 Hz, 3.5 kHz 380 Hz, 3.5 kHz
Amplification External P4, 850 W External P4, 850 W Built in, 350 W
Bass (−6 dB) 25 Hz 32 Hz 25 Hz
Linearity (±2 dB) 50 Hz to 12 kHz 60 Hz to 12 kHz 60 Hz to 17 kHz
Max. SPL (1 m) 121 dB 118 dB 117 dB
Size (H × W × D) 1500 × 500 × 580 mm 1586 × 398 × 535 mm 884 × 498 × 568 mm, plus 200 mm stand
Input sensitivity 2 V 2 V 1 V, with rear trim

Choose the SCM300ASLT If You

  • Need the most output for a large room: 121 dB, versus 118 and 117 dB.
  • Want flat bass lower down: ±2 dB from 50 Hz, versus 60 Hz on the other two.

Choose the SCM200ASLT If You

  • Need a narrower speaker: 398 mm wide versus 500 mm, with the same P4 amplification.

Choose the SCM150A Classic If You

  • Want the amplifiers inside the speaker, with no rack or speaker-to-amp cables to plan.
  • Need a shorter speaker on a stand that still reaches 25 Hz.

Not Sure Which to Choose?

The SCM300ASLT or the passive SCM300PSLT? Or the SCM200ASLT or SCM150A Classic? Todd can talk it through with you.

Available Finishes

Choose Your Finish

Standard veneers Cherry, Walnut, Oak, Black Ash
Standard paints Satin Black, Satin White
Premium veneers (up-charge) Rosewood, European Crown Cut Walnut, Burr Walnut, Pippy Oak, Burr Magnolia, Burr Poplar
High gloss (up-charge) Clear High Gloss Veneer, Piano Black, Piano White

Planning and Setup

1Step 1: Plan the Space

  • Each speaker is 1500 mm tall, 500 mm wide and 580 mm deep, and weighs 96 kg.
  • Each P4 goes in a 19-inch rack (5U) or free-standing on sturdy shelving. Air enters at the back and leaves at the front, so never block either vent or enclose the amplifier.
  • The P4's fans start when its heatsink reaches about 30 °C and keep running until it cools to about 20 °C, even in standby. Keep that in mind when choosing where it sits.
  • The cable from each P4 to its speaker is 5 m as standard. 10 m cables are available, and runs up to 20 m are possible by splicing 4 mm² cable onto a 10 m cable.
  • Each P4 needs an earthed mains connection.

2Step 2: Unpack and Position

  • These are large, heavy speakers: unpack them with a second person, in a large open space near their final position.
  • Keep the speakers away from corners and walls to reduce low-frequency problems.
  • Carpets, curtains and soft furnishings help control reflections in the midrange and treble.

Todd can help you work out positions, cable runs and where the amplifiers should go before delivery.

3Step 3: Connect

  • P4 to speaker: one 8-way cable per speaker.
  • Source to P4: a balanced XLR cable from your preamp or source to each P4 (pin 1 screen, pin 2 hot, pin 3 return). Plan on supplying your own XLR signal cables; Todd can confirm what's in the box.
  • Level: volume is set at your preamp or source.
  • Unbalanced sources: use an XLR-to-RCA cable. If you hear hum, disconnect the screen at one end.
  • Mains: use the supplied lead and check the voltage shown on the P4's panel matches your supply.

4Step 4: Power On

  • Switch on each P4 separately, one after the other, to limit the inrush current.
  • Set the rear isolation switch to ON, then press the front standby button once.
  • The P4 runs its self-checks: the indicator changes from green to orange, blue flashes, red shows briefly as the mute releases, then the indicator settles on steady blue. It's ready to play. Start with the volume low and raise it gradually.
  • A short sound from the speakers when power is applied or removed is normal and harmless.

5Step 5: Everyday Use

Standby Press the standby button: the blue light goes out and only green remains.
Occasional red during loud playback The P4 is briefly reducing gain to protect the drivers. Turn the level down a little.
Steady orange A fault or power-up failure has shut the amplifier down. Press standby to restart; after overheating, let it cool first. If there's no response, check the rear fuse; if a replacement fuse also fails, call Todd.
Custom installation A 5-pin remote interface on the P4 provides standby control and status outputs for a control system.

Specifications

ATC SCM300ASLT

Type 3-way active floorstanding loudspeaker, four amplifier channels per speaker
Drivers HF 25 mm soft dome; Mid 75 mm Super Dome; LF 2 × 375 mm Super Linear
Amplitude linearity (±2 dB) 50 Hz to 12 kHz
Cut-off (−6 dB, free-standing) 25 Hz and 20 kHz
Dispersion ±80° horizontal, ±10° vertical, coherent
Max. continuous SPL (1 m) 121 dB
Crossover 380 Hz and 3.5 kHz; even-order, critically damped active filters
Input Female XLR, balanced >10 kΩ, 2 V sensitivity
Amplifier output Bass 275 + 275 W, mid 200 W, high 100 W per speaker (ATC P4)
Overload protection Active FET momentary gain reduction plus thermal tweeter protection
LF EQ +6 dB at 40 Hz
Speaker cable 8-way cable per speaker, 5 m standard; 10 m available
Dimensions (H × W × D) 1500 × 500 × 580 mm (59.1 × 19.7 × 22.8 in)
Weight 96 kg per speaker
Warranty 6 years

ATC P4 Amplifier (One Per Speaker)

Output per channel Bass 1: 275 W into 8 Ω; Bass 2: 275 W into 8 Ω; Mid: 200 W into 16 Ω; HF: 100 W into 6 Ω (850 W total)
Crossover Active, 380 Hz and 3.5 kHz, 4th order with phase correction
Input Balanced XLR, 2 V sensitivity, >10 kΩ
Frequency response 5 Hz to 20 kHz, ±0.1 dB
Signal-to-noise / crosstalk Better than 105 dB / better than 90 dB
Protection Active FET momentary gain reduction (soft limiting)
Cooling Three fans
Mains 100, 115 or 230 V, 50/60 Hz, set at the factory for your region
Power consumption 150 VA in standby, 1200 VA maximum
Size 19-inch rack mount, 5U (222 mm) high; 538 mm overall depth including front and rear handles
Weight 35.8 kg (78.8 lb)

Order Your ATC SCM300ASLT

As an authorized ATC dealer, TTVJ handles your order personally, from confirming the configuration to delivery. Reach Todd by phone or message to:

  • Confirm current pricing and availability
  • Discuss a trade-in of your current speakers
  • Ask about financing and shipping